Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

KČ-190

Chlorinated Rubber Enamel
For interior use
For exterior use
The product can be applied by brush
The product can be applied with spray gun
Use appropriate solvent for diluting and tools cleaning
Drying time 16 h
Packaging 0.9 l, 2.7 l, 10 l, 23 l
Consumption 7 - 11 m²/l
Nearest store
Consumption calculator
Description
Usage

Chlorinated Rubber Enamel KČ-190 is intended for effective and long-lasting corrosion protection of steel, aluminium and galvanised surfaces designed for use in atmospheric conditions, including industrial and marine atmospheres. It forms a black, elastic, semi-gloss coating with a high resistance to water and salt. May be used for painting pre-primed and unprimed steel surfaces. In most cases, pre-priming increases the efficiency of the protective coat. Recommended primer for priming of steel surfaces: EPOPRIM (1-2 coats with the total dry coat thickness of up to 100-120 microns). Recommended primer for priming of aluminium and galvanised surfaces: either VL-02 or EPOPRIM (by applying a single coat with the dry coat thickness of 40-50 microns).

Mix before use. 2 coats should be applied on pre-primed surfaces using a brush, a spray gun or the immersion technique. When painting unprimed steel products, 3 coats should be applied on previously thoroughly de-rusted and degreased surfaces. No pre-dilution required when applying with a brush. When applying with a spray gun or using the immersion technique, the enamel should be pre-diluted with xylol or the SOLVEKS SPRINT solvent: up to 25% for the immersion technique and up to 40% for application with a spray gun. The same solvents should be used for washing the tools. While painting, the temperature of the ambient air and the surface to be painted should not be below minus 10°C, and the relative humidity should not be higher than 85%. The drying time between the coats is 1.5 hours at +20°С and 4 hours at minus 10°C. At the temperature of +20°C, the drying time until the attainment of the required mechanical strength is 16 hours. The consumption for each layer (not counting the losses during the application) is 7-11 m2/l. Store in tightly closed containers and protect from direct sunlight. Frost-resistant.

Need help?
info@rilak.lv
+371 67 458 776
Question about the product
Description

Chlorinated Rubber Enamel KČ-190 is intended for effective and long-lasting corrosion protection of steel, aluminium and galvanised surfaces designed for use in atmospheric conditions, including industrial and marine atmospheres. It forms a black, elastic, semi-gloss coating with a high resistance to water and salt. May be used for painting pre-primed and unprimed steel surfaces. In most cases, pre-priming increases the efficiency of the protective coat. Recommended primer for priming of steel surfaces: EPOPRIM (1-2 coats with the total dry coat thickness of up to 100-120 microns). Recommended primer for priming of aluminium and galvanised surfaces: either VL-02 or EPOPRIM (by applying a single coat with the dry coat thickness of 40-50 microns).

Usage

Mix before use. 2 coats should be applied on pre-primed surfaces using a brush, a spray gun or the immersion technique. When painting unprimed steel products, 3 coats should be applied on previously thoroughly de-rusted and degreased surfaces. No pre-dilution required when applying with a brush. When applying with a spray gun or using the immersion technique, the enamel should be pre-diluted with xylol or the SOLVEKS SPRINT solvent: up to 25% for the immersion technique and up to 40% for application with a spray gun. The same solvents should be used for washing the tools. While painting, the temperature of the ambient air and the surface to be painted should not be below minus 10°C, and the relative humidity should not be higher than 85%. The drying time between the coats is 1.5 hours at +20°С and 4 hours at minus 10°C. At the temperature of +20°C, the drying time until the attainment of the required mechanical strength is 16 hours. The consumption for each layer (not counting the losses during the application) is 7-11 m2/l. Store in tightly closed containers and protect from direct sunlight. Frost-resistant.

Question about the product
Patēriņa kalkulators

Contact us

We will be happy to help

Consumption calculator

Find out how much of the product You will need.

Produkts:
Consumption
KČ-190
7 m²/l
Surface area
Based on our calculations You will need approximately:
0
liters of product for one coating

SIA Rīgas laku un krāsu rūpnīca

Daugavgrīvas iela 63/65, Rīga, LV-1007

Reģistrācijas Nr.: 40003284444

PVN Nr.: LV40003284444

Banka: A/S Swedbank

Konts: LV23HABA0019308047593

Bankas kods: HABALV22

Contact us

We will be happy to help